A generator can start on the first crank and still fail under a real house load. The voltage may sag, the frequency may drift, or the coolant temperature may climb once the air conditioning and the pool pumps come on. A load-bank test record proves the set can carry the load, not just idle. It prepares the generator and the bank, steps the load in a fixed sequence, logs the temperature and fuel, and verifies the transfer and shutdown. The record is the evidence a coastal estate needs before storm season.
Key takeaways
- Record the generator rating, the load bank, and the test setup.
- Step the load in fixed increments and hold each step.
- Log voltage, frequency, temperature, and fuel at every step.
- Test the transfer switch and the controlled shutdown.
- Set an annual and post-storm test calendar with owners.
Prepare the generator and the load bank
Record the generator make, model, rated kW, and fuel type. Note the hour meter, the last service, and the oil and coolant condition. Add the battery date and the block heater status. A set that has not run under load for a year is not proven. The record should start with the condition of the machine, not only the test result.
Record the load bank make, capacity, and cable configuration. Note the connection point, the breaker size, and the grounding arrangement. Add the ambient temperature and the altitude, because both affect the rating. A load bank that is too small cannot prove the set. The record should show that the bank can reach the target load.
Walk the site and record the exhaust path, the cooling air, and the clearance around the set. Note any debris, nesting, or corrosion at the terminals. Add the fuel level and the condition of the day tank. A coastal generator may have salt corrosion that inland sets do not. The record should show the inspection before the test.
Record the safety brief, the fire watch, and the person in charge. Note the communication method and the emergency stop location. Add the utility status and the transfer switch mode. A load test on a live transfer switch needs a clear plan. The record should show who was allowed to operate what.
Step the load in a fixed sequence
Start the generator and record the no-load voltage, frequency, and oil pressure. Note the run time before the first step. Add the ambient and the coolant temperature. A set that cannot hold no-load voltage will not improve under load. The record should establish the baseline before any load is applied.
Apply the load in fixed steps, such as 25, 50, 75, and 100 percent of the rated output. Hold each step long enough for the temperature and frequency to settle. Record the voltage, the frequency, the current, and the power factor at each step. A short step can look stable while the set is still recovering. The record should show the hold time.
Record the coolant, oil, and exhaust temperatures at each step. Note the fuel consumption and the hour meter reading. Add any alarm, derate, or automatic shutdown. A set that reaches the target load but overheats is not ready. The record should show the limiting condition, not only the maximum load.
Record the return to no load and the cool-down period. Note the voltage and frequency recovery and any abnormal noise. Add the time to stable idle. A set that shuts down abruptly can damage the turbocharger or the windings. The record should show a controlled sequence from start to stop.
Log the electrical and mechanical readings
Record the voltage and frequency at each phase and the balance between phases. Note any phase that is significantly lower or higher. Add the current and the real and apparent power. An unbalanced load can overheat one winding while the total looks fine. The record should show the per-phase values, not only the total.
Record the oil pressure, the coolant temperature, and the intake air temperature. Note the fuel pressure and the filter differential where gauges exist. Add any abnormal vibration or exhaust colour. A generator can carry the load and still be close to a failure. The record should capture the mechanical signals beside the electrical ones.
Record the battery voltage and the charging current during the run. Note the alternator output and any fault code. Add the condition of the battery terminals and the cable connections. A set that starts on a weak battery may not restart after a long outage. The record should show the charging system, not only the engine.
Record the fuel level before and after the test and calculate the consumption per hour at each step. Note the fuel quality and the age in the day tank. Add the plan for polishing or rotating the fuel. A coastal site with stored fuel needs a water and microbial check. The record should connect the test to the fuel maintenance schedule.
Test the transfer and the shutdown
Test the automatic transfer switch with the utility available and with the utility simulated as lost. Record the transfer time, the voltage, and the frequency at the load. Note any load that dropped or restarted. Add the retransfer time and the synchronization. A transfer that is slow or rough can damage sensitive equipment. The record should show both directions.
Test the generator with the actual house load, not only the resistive load bank. Note the air conditioning, the pool pumps, the elevator, and the security system as they start. Add the starting current and the voltage dip. A set that passes a load bank can still trip on a motor start. The record should show the largest step the house can present.
Test the low-fuel, high-temperature, and low-oil shutdowns where the set allows a safe simulation. Record the alarm and the shutdown time. Note the reset procedure and the person who performed it. A safety shutdown that does not work is a serious defect. The record should show the test, not only the setpoint.
Record the final shutdown, the cooldown, and the return to automatic standby. Note the fuel top-up, the breaker position, and the transfer switch mode. Add the date and the person who released the set. A generator left in manual after a test is a silent failure waiting for the next storm. The record should end with the automatic state confirmed.
Set the annual and post-storm calendar
Write an annual load-bank test with the date, the target load, and the owner. Note the service that must precede it, such as an oil change or a coolant check. Add the load bank rental or the contractor booking lead time. A test that is scheduled after the storm season is a review, not a preparation. The calendar should put the test before the risk.
Write a monthly exercise that runs the set at a meaningful load for a fixed period. Note the load source, the duration, and the readings. Add the automatic transfer test where it can be done safely. A monthly no-load run keeps the battery and the fuel moving but does not prove capacity. The record should distinguish exercise from proof.
Write a post-storm inspection that covers the fuel, the air intake, the exhaust, the battery, and the transfer switch. Note the run hours and any fault code. Add the decision on an oil sample or a service. A set that ran for days during an outage needs more than a visual check. The record should show the follow-up.
Review the test record with the owner and the generator technician each year. Ask whether the load has grown and whether the set still covers the critical circuits. Record the decision on an upgrade or a load-shedding plan. A new pool or a new HVAC system can change the answer. The review should look at the house as it is now.